When it comes to the success of your home repair and improvement project there is nothing more important than to complete the project with no injuries! I remind my self of the safety rules each time I use a tool, especially a power tool. That is why after 25 +/- years I have yet to sustain a major injury, knock on wood. (I cut my thumb pretty bad with a utility knife one time in my youth not having employed proper knife safety). However my appendages are all in place, I have no broken bones, no back problems or knee problems. I want the same for you.
Secondly, it is also important to use the saw properly so that you end up with a pro looking job!
Miter Saw Blade
What is a circular saw (also known as a skill saw)? In our example it's the kind of saw that is hand held on top of the material that is to be cut and has a circular blade. Hence the name. The area of the saw that rests on the material is called the shoe plate. The blade comes in sizes most commonly from 4" to 8". For general cutting purposes on home projects a size 7 ¼" is most common. If someone asks you what size saw you have, the proper answer is to tell them the blade size. Blades also come with varying numbers of teeth. The number of teeth on the blade should be right for the material and the direction of the cut. When cutting along the length of the wood (with the grain, called a rip cut) use fewer teeth. When cutting across the wood (across the grain, called a cross cut) use more teeth. If the wood is harder, use more teeth. Carbide tipped blades are better. When properly installed for wood cutting, the teeth on the front of the blade should be pointing up. For cutting other things, such as vinyl siding, the blade can be put on "backwards". Always disconnect the power cord when changing blades. Don't use an overly dull blade. Blades can be changed easily: First, it helps if you set the blade depth to shallow. Second, find the blade lock on the outside of the saw. It's kind of like a metal button that you push. Then find a wrench that fit's the retaining bolt in the center of the blade. When you buy circular saw blades make sure the arbor (the hole in the center of the blade) is the right fit. Next, push down on the blade lock and turn the blade until you feel it lock. Now you can unscrew the retaining bolt counter clockwise. Once the bolt is removed, lift the blade guard to remove the old blade. Install the new blade using reverse procedure.
Most circular saws will typically have 2 adjustments. One is the bevel adjustment. This is the one that tips the saw blade from side to side. This in turn causes the saw to cut at an angle. Use at 0 degrees for straight cuts. The other is the blade depth. This is the one that allows the blade and the motor to slide up and down in relation to the shoe plate. This causes the blade to cut deeper or shallower into the material. Usually these adjustments are held in place with nut and bolt type fasteners. The nuts will come in varying shapes and sizes. Be sure they are tight before using the saw. Also don't forget to unplug the saw before making adjustments.
The on-off switch is a trigger/toggle type which may or may not have a safety latch. Release the safety (if it has one) and "pull the trigger" to actuate the blade. Don't forget to release the trigger when you are finished making the cut!
As far as making a cut goes there are a few things I like to remember before I do: Cut outdoors if you can. If you cut with the wind at your back, it will blow the sawdust away from you. Have good lighting. Wear eye and ear protection. Wear shoes and socks. Avoid loose clothing and any other object that can come close to the blade. Avoid distractions that can suddenly cause you to loose focus. Adjust the saw for angle and depth. Make sure the material is stable and won't move around as this can result in injury and/or a poor cut. In the absence of a helper, I like to use clamps when working from a saw horse. If you are working from a pile you can sometimes put foot or knee pressure on the material to keep it steady. Use common sense though and don't try anything that doesn't seem right. Remember: sawdust on plywood can make it slippery when walked on. Pay attention to what is under the material you are cutting. Whatever comes in contact with the material along the line of your cut will be affected by the blade in the same way the material is. This includes fingers! Put something under the material to avoid unwanted contact with the blade. Shade your eyes from bright sunlight. Make sure the mark you are cutting along is clearly visible. Cut with the back of the material (the side that won't show when installed) on top. This will insure that the side that shows will have a nice clean cut with no "feathers". Make sure the power chord of the saw is trailing behind the saw and can't be cut accidentally. Adjusting the blade depth to approx. 1/8" below the material helps with avoiding unwanted outcomes.
(Warning! Kickback is when the back of the blade binds and causes the saw to suddenly jump violently away from the material, and possibly out of your hand, causing possible injury, damage to the material and damage to the saw. One way to avoid this is to go slow with your cut. If you feel resistance and notice the motor wind down, kickback could be imminent! Stop forward motion with your saw. Release the trigger and hold the saw steadily in place until the blade comes to a complete stop. This type of kickback usually occurs when making a rip cut and is caused by the wood having natural tension in it, pinching the back of the blade. To remedy this problem, place a wedge in the curf (the portion of the material that is taken out by the blade) in between the two sides of the cut. Other ways kickback can occur are if you or the material or the saw gets bumped or are otherwise disturbed. This can cause the back of the blade to be moved to the side causing it to bind. Another way is if you let go of the saw while it is still in the material and the blade is still moving. Still another way is if you try to cut a radius. Circular blades are intended for straight cuts, straight blades, like jigsaw blades, are intended for circular cuts. If you use it for anything else you are taking your chances. Don't try to cut the wood in between the sawhorses, always on the outside. More specifically, never have the material supported on both sides. Support the long side of the board and have the short side be free of contact. Kickback can also occur if the blade has contact when you "pull the trigger". But mostly, avoid kickback by paying attention to how much pressure is on the back of the blade.)
Now you are ready to make a cut. I like to start with just the front end of the shoe plate resting comfortably on the material. Make sure the blade is not touching the material when you "pull the trigger". Set the blade in line with the cut line so that it is on the side of the line that is the "waist" side. Make a few small "test" cuts moving the blade closer to the line each time. When you finish the cut, the mark should still be visible but get as close to it as you can. Remember: you can always take more off the board if it is too long but you can't put more on if it is too short! Make sure the power chord can move freely. Try to relax as you make the cut. Be gentile with your motions. If you fight the saw, the saw will probably win. Cutting slowly will make a better cut. Focus your vision on the blade, not on the wood, from the handle side of the saw. Make sure the shoe plate is resting completely and flatly on the material. Less side to side motion makes a straighter cut. The blade can be maneuvered to stay on the line but watch for kickback. I like to push the saw with my body rather that with my arm. Cut past the end of the cut. To avoid the "chink" that can occur when the waist side falls off, place an object that is about 1/4" to 1/2" below the waist piece so that it doesn't fall too far.
This is in no way intended to be an exhaustive essay. It is just a few notions I had on a Sunday afternoon while thinking about my circular saw. Use your own good judgment. Leave a comment and Happy Sawing!
Cyber Monday Bosch PRO12CASE 12-Inch Saw Blade Carrying Case 2011 Deals
Dec 01, 2011 00:42:51
Click for larger image and other views
Cyber Monday Bosch PRO12CASE 12-Inch Saw Blade Carrying Case Feature
- Rugged carrying case for 12-inch circular saw blades
- Fully protects valuable blades during transport, storage, or shipping
- Reinforced textile construction with Velcro strips and heavy snaps
- Built-in carrying handle offers additional storage space for blade extras like wrenches, keys, bushings, or stabilizers
- 0.7 by 16.5 by 15.5 inches; weighs 2 pounds
Cyber Monday Bosch PRO12CASE 12-Inch Saw Blade Carrying Case Overview
Expand the use of Bosch power tools with attachments.Cyber Monday Bosch PRO12CASE 12-Inch Saw Blade Carrying Case Specifications
About This Bosch Carrying CaseThis Bosch carrying case is designed to protect your valuable 12-inch circular saw blades from damage, whether you're storing them, transporting them, or sending them off to be sharpened. The innovative reinforced textile carrying case features an embroidered Bosch logo, large Velcro strips and heavy snaps, plus a built-in carrying handle that offers space for another blade and additional accessories such as wrenches, Allen keys, bushings and stabilizers. It's even equipped with a blade sharpening indicator.
About Bosch Professional Series Circular Saw Blades
The new line of Bosch Professional Series circular saw blades are designed to meet the needs of professional users from woodworkers to firefighters. All blades feature industrial quality, laser cut, fully hardened bodies and oversized carbide tips for resharpening. Bosch offers a wide variety of woodworking blades in the Professional Series line including blades specifically forged for applications like fine ripping, crosscutting, finishing, planer/combination, slide miter, melamine/veneer/laminate, solid surface and dadoes. These blades feature oversized resharpenable carbide tips, patented C-4 Dyanite carbide that stays sharp up to six times longer than standard carbide, tri-metal shim braze for extreme shock resistance, and an anti-friction coating.
SAVE NOW on Cyber Monday offers below!
Available In Stock. |
| This Cyber Monday Bosch PRO12CASE 12-Inch Saw Blade Carrying Case ships for FREE with Super Saver Shipping. |
Price : Click to Check Update Prices Please. |
