If you enjoy playing cornhole and are a do it yourself kind of person, here is a set of simple cornhole game plans for how to make a cornhole game set, along with the plans is a list of suggested tools. We hope that you enjoy creating your own cornhole set using our simple cornhole designs. After you review these plans, you will be showing others how to make cornhole boards in no time. These plans use standard cornhole dimensions.
SUGGESTED TOOLS AND SUPPLIES
1 1/2" plywood sheet -4'x 8'
3 2" x 4" boards - 8' long
1 box of deck screws
Miter Saw Blade
Tape Measure
Jig saw
Drill
Circular or mitre saw
150 grit sandpaper
Step by Step Instructions
Step One
Take the 4x8 sheet of plywood and cut it into four equal sections, all 2x4. Then take one section and cut it into 4 sections that are 11 1/2" x 2'.
Step Two
Take two of the 2x4x8' boards and cut then into 4 equal lengths. They should be 3'x11 1/2". They are this size so that a riser can be added later on to tilt your finished board.
Step Three
Next take each of the 3'x11 1/2" boards and attach then with deck screws to each of the long sides of the platforms. Leave a 1/2" gap at the end you want to be the top of the game board.
Step Four
Measure between the side rail boards for the exact measurement for the top and bottom rails on each platform, then cut the remaining 2 x 4 to match those measurements. Then attach those cut pieces, on edge,with deck screws through the side pieces.
Step Five
Set the platform on the ground, right side up. You are about to find the cornhole position so, go to the top of the board. That is the end that does not have a rail. Find the center of the cornhole by measuring 9" from the top, then 12" from each of the sides. This will give you the dead nuts center of the cornhole. Now use a compass or a nail with a 3" piece of string attached to it and a pencil to draw a complete circle. After drawing the circle drill a hole in the center that is large enough to insert the blade of your jigsaw. Begin cutting out the circle you drew. After cutting out the hole then use the sandpaper to smooth out the edges.
Step Six
Now take one of the 11 1/2" x 2' boards and attach it above the cornhole. It will fit into that 1/2" gap and be affixed with deck screws to the side boards.
You are now ready to play cornhole. If you want to paint the boards we recommend that you use a primer and then gloss enamel. If you use outdoor/house paint the paint job should last as long as your boards.
If you want to make your own cornhole bags, please check out the article I have written and posted on this site. It is a detailed instructional on how to sew them yourself. It is a lot easier to buy your set and bags, but I hope the do-it-yourself people out there are able to use these instructions.
Christmas Sales Freud D1060X Diablo 10-Inch 60 Tooth ATB Fine Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating 201
Dec 25, 2011 12:09:36
Click for larger image and other views
Christmas Sales Freud D1060X Diablo 10-Inch 60 Tooth ATB Fine Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating Feature
- Features Freud's TiCo Hi-Density Carbide with Titanium for long life and a flawless finish
- Super thin laser cut kerf gives extremely fast, durable, and clean cuts
- Non-Stick Perma-Shield coating to resist heat and reduce pitch build-up
- Laser-cut stabilizer vents trap noise and vibration keeping the blade cool and reducing blade warp
- Tri-Metal Brazing for impact-resistant tips
Christmas Sales Freud D1060X Diablo 10-Inch 60 Tooth ATB Fine Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating Overview
This Diablo saw blade is designed to meet the needs of the construction and remodeling market. This advanced laser cut blade features a thin kerf, making it ideal for portable and low powered saws on the jobsite. Features Freud's TicoHi-Density Carbide , a Perma-Shield coating keeps this blade free from gumming and corrosion, Laser-cut stabilizer vents reduce vibration and heat buildup for more precise cuts and longer cutting life, and tri-metal brazing. This particular blade is the ideal choice for trim carpenters because it leaves a smooth surface that requires little to no sanding. It's ideal for crosscutting oak, pine, melamine, plywood, and moulding.10" diameter, 60t ATB, 5/8" arbor, 15 Degree hook angleChristmas Sales Freud D1060X Diablo 10-Inch 60 Tooth ATB Fine Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating Specifications
For a clean-cutting blade that creates smooth finish cuts in material such as veneer plywood and delicate hardwood, look no further than the D1060X Diablo 10-Inch Fine-Finish Saw Blade. This is your go-to blade for slicing through oak, pine, melamine, veneer plywood, and delicate molding. This blade's high tooth count minimizes grabbing of the workpiece, producing cuts that require little to no sanding. For strong, long-lasting resistance, the blades feature a tough steel plate and high-density carbide tips. |
 |
|
Achieving attractive results when working with fine finish material is all about clean, accurate cuts. The Freud D1060X makes this process easy, fast, and precise. To save you time, most cuts made by this blade require little to no sanding.
Trim carpenters, fine cabinetmakers, and avid do-it-yourselfers will want to keep this blade on hand for those special jobs that call for making smooth crosscuts in fine finish work. Appropriate application materials include oak, pine, melamine, veneer plywood, and delicate molding.
Produces Smooth, Quiet Cuts with Laser-Cut Kerf
The Freud D1060X's clean-cutting design means that you can enjoy the comfort of smooth performance. The thin 0.98-inch kerf between the blade's 60 Hi-ATB (alternate-top bevel) teeth is laser cut to provide ease of feed, so you have more control over the blade's position. This helps maximize both the accuracy of the cut and the efficiency of your work, so you enjoy a job well done and the ability to complete more tasks in less time.
An added bonus, the blade's laser-cut stabilizer vents reduce noise and vibration during operation, keeping your work environment more relaxed and your hands more in control. This feature also reduces friction and warping, helping to extend the blade's cutting life.
Features Shock-Resistant Carbide for Long-Lasting Precision
So you can count on it over the long term, the Freud D1060X is designed for durability. The blade's hardy teeth are protected by Freud's exclusive shock-resistant TiCo Hi-Density Carbide formula, which helps fight wear and tear and maintains blade sharpness up to four times longer than standard carbide. And protecting the blade is Perma-Shield Non-Stick Coating that provides resistance to heat and corrosion.
Fits Miter and Table Saws
The Freud D1060X is a great addition to your workshop because it's designed with the versatility to fit a variety of miter and table saws.
This product is covered by Freud's Limited Lifetime Warranty.
What's in the Box
Freud D1060X Diablo 10-Inch Fine-Finish Saw Blade.
SAVE NOW on Christmas Sales Offers below!
Available In Stock. |
| This Christmas Freud D1060X Diablo 10-Inch 60 Tooth ATB Fine Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating is cheap and shipping as well. |
Price : Click to Check Update Prices Please. |
